Condividi su condividi pagina su facebook condividi pagina su twitter Posizione nel sito. Adesso sei in: Home , RTX , Base , Elecraft K2 - Usato-

Elecraft K2 - Usato-

Elecraft K2 - Usato-

Elecraft K2 - Usato-

Elecraft K2 - Usato-
K2 STANDARD FEATURES Specifications and Pricing subject to change without notice. •Rugged, attractive custom enclosure •Small, portable size: 2.9h x 7.8w x 8.2d inches •Weight 3.3 lbs. (excluding internal options) •80-10 meter ham band+ coverage; 160 m optional •Efficient 12 Volt (10 - 15 V) operation for home or field •Receive current as low as 150 mA (battery save mode) •CW-only or SSB/CW + Digital Modes with SSB option •Back-lit LCD and LED bargraph; day/night settings •PLL synthesized--low phase noise Microprocessor controlled •3 transverter bands; programmable display, I.F., power •Dual VFOs with split operation. •Direct keypad entry of frequencies and memory channels. •RIT and XIT with four offset ranges •Built-in high-efficiency speaker •Memories store mode, VFO A/B, split, RX filter, etc. •Simple menu system for advanced settings. (Up to two menu functions can be assigned to the two programmable front panel function keys.) •Room for additional connectors on the rear panel •Smart ‘hunt and pounce’ band-scanning mode RECEIVER •Low-noise, single-conversion superhet receiver •Double-balanced diode mixer for excellent dynamic range •Receive sensitivity: 0.15 uV (pre-amp on, typical.) •Narrow ham-band, double-tuned bandpass •RX/TX filters, relay switched for better IMD response •Smooth, fast attack, I.F.-derived AGC (no "popping") •Switchable preamp and attenuator •Variable-bandwidth I.F. crystal filtering •Multiple VFO tuning rate selections •10 Hz tuning resolution •Bar graph S/RF OUT/ALC meter •Adjustable squelch TRANSMITTER •Adjustable 0.1-15 W (K2), 0.1 – 100W (K2/100) •Rugged, SWR-protected, push-pull PA transistors •Programmable current limit for battery operation •Harmonics and spurious outputs: Better than –40 dBc CW FEATURES •Full diode switched break-in with variable QSK delay (Both at QRP and 100W levels) •9-memory keyer; iambic A and B; adjustable weight •9-50 wpm (internal keyer); 70+ wpm (external keying) •Programmable message repeat interval •Simultaneous computer and paddle CW keying inputs •Variable bandwidth crystal filter (approx. 200 - 2000 Hz) •Adjustable RX CW offset with tracking TX side tone. •Selectable opposite sideband RX for QRM reduction K2 and Accessories Click on underlined part numbers for details. K2 HF Transceiver KAT100-1 100W Ext. ATU KPA100 100W Option (K2 + KPA100 = K2/100) KAT100-2 100W ATU w / EC2 Panels KSB2 SSB Option KAT100PNL Converts KAT100-1 to -2 K160RX 160M, 2nd RX Antenna Option KBT2 Internal Battery Kit KNB2 Noise Blanker Option KBT2-X (KBT2 w/o Battery) KDSP2 Advanced Internal DSP Filter and Clock BATT Replacement Battery KAF2 Audio Filter and Clock EC2 Blank Project Enclosure KIO2 RS-232 Interface ETS15 1.5" Tilt Stand for EC2, KAT100 KAT2 20W Internal ATU ETS2 Std 3" Tilt Stand for EC2 K60XV 60M and Transverter Adapter Microphones Proset-K2 Heil Boom Headset for the K2 Transverters (K2 and most HF rigs) Band Decoder (K2 and most HF rigs) XV50 6 Meter Transverter KRC2 Band Decoder for Ant Relays XV144 2 Meter Transverter XV222 222 MHz Transverter XVOVN Crystal Oven for XV
ultima modifica: 12/04/2018 Claudio F.

Richiedi informazioni











 

tutti i campi sono obbligatori